叠门宽
图I
A ,示意图表明完整的纸样，细节阐明请看下页。
B,当钮扣基地坐落服装基地线上时，钮扣将有一半在基地线左面，一半在基地线右边，
这就需求有必定的叠门宽。
C, 叠门宽等于钮扣直径。

图 2
示意图表明钮扣、扣眼、叠门宽与前基地线的联系。
扣眼长度
扣眼长度等于钮扣直径加 1/16英寸（0.3CM）。关于球
形、宝石形或特别形状的钮扣，有必要留出大于 "#$ 英寸
（0.3CM）的余量。要断定所需余量，可先从织物废料上剪
一条缝，将钮扣套进去，以钮扣能顺畅地穿过来断定扣眼
的尺度。

在无领或有外接领的领线时，扣眼的方位
在无领或有外接领的领线时，扣眼坐落间隔领线 0.5
倍的钮扣直径再加 1/4英寸（0.6CM）处。参看图 "。
翻领领线时扣眼的方位
翻领扣眼有必要放置在翻领驳点处。扣眼操控着翻领驳
点，参看“双排扣服装的扣眼”一节图 "。
系腰带的服装
服装系的腰带在腰线上部或下部；设计扣眼时请求腰
带或带扣间隔钮扣最少 1 1/2英寸（3.8CM），参看图 "。
无腰带服装的扣眼方位：关于无腰带服装，则有必要在
腰围线上设置扣眼，无需考虑服装是不是有腰缝。这将确保
服装在腰围处紧身合体。在大衣或套装上，有时候需求将
扣眼设置在间隔腰线上或下1/8-1/2英寸（0.3-1.3CM）
处，以求取得必定的效果。
设计扣眼闻的间隔
断定了领线邻近及腰线处扣眼的方位后，根据所需钮
扣的数量来划分余下的空间。可能的话。在胸围处设置扣
眼，以防服装有豁口。
最终给坐落服装中心的扣眼划样。
钮扣眼最少向基地线左面移 1/16英寸（0.3CM），为扣襻留下余量（图示为正面）。一些
新式钮扣有很宽的扣襻，当运用这类钮扣时，先丈量扣襻宽度，再将钮扣眼向左移扣襻的一
半宽度（图 2）。
扣襻宽度不影响扣眼尺度。如图，扣眼从右边 1/16, 英寸（0.2CM）或更大些开端。
贴边
A,贴边可以如图 " 所示，剪成一片或分隔。这么贴边有必要满足宽，能比扣眼再长出至
少 1/16, 英寸（0.2CM），并且在领圈线、肩线、腰围线处的形状一样。
B,沿止口线折叠纸样。在折纸不和描出领线、肩线和腰围线及省道线，在肩线和腰线
处做上符号。
C 在两符号间画一直线，再画出造型线（如图 "）所示。

Stack gate width
Figure I
A, schematic diagram shows complete pattern, clarify the details see next page.
B, when the button base is located clothing base line, the button will have half at the base line in the left half of the base line on the right,
This needs to have a certain degree of fold door wide.
C, the width of the stack is equal to the diameter of the button.
Figure 2
The diagram of buttons, button hole, folding door width and former base line contact.
Buttonhole length
Buttonhole length equal to the button diameter plus 1/16 inch (0.3CM). About ball
The shape, the shape of the special shaped gem or buttons, it is necessary to set aside more than #$. "
(0.3CM) margin. To determine the required allowance, you can cut the fabric waste
A crack, the buttons are set to go, the button can smoothly pass through that buttonhole
Scale.
In the absence of an external collar or collar collar line, buttonhole position
In the absence of an external collar or collar collar line, collar line 0.5 is located between.
Times the size of the button plus 1/4 inches (0.6CM) office. See figure".
The collar line range.
It is necessary to place the barge Lapel buttonhole point in lapel. Control barge Lapel buttonhole
See, "double breasted clothing buttonholes" section map".
Wearing a belt
Department of fashion belt in the upper or lower waist; when the waist design request.
With or with a button with a minimum of 1 1/2 inches (3.8CM), see fig.".
Buttonhole directions without clothing: no belt belt of clothing, it is necessary to
Waist line set buttonholes, without considering the clothing is not a waist seam. This will ensure
Clothing in waist circumference tight fit. Sometimes on a coat or a suit, the demand will be
Buttonhole set in the waist or 1/8-1/2 inch interval (0.3-1.3CM)
In order to achieve a certain effect.
The design of buttonhole smell interval
That collar line adjacent and waist hole position, according to the required button
The number of buttons to divide the rest of the space. Possible words. Buckle set in the chest at
The eye, to prevent clothing with a gap.
Finally to center is located clothing like row buttonhole.
Button hole to the base line shift left at least 1/16 inches (0.3CM), left the balance button loop (shown as positive). some
New buttons are a wide button loop, when the use of the button. The first measure buckle loop width, then the button hole to the left shift button loop of a
Half width (Figure 2).
The button loop width does not affect the scale. Figure 1/16 inches from the right eye, (0.2CM) or more beginning.
Welt
A, as shown in Figure welt ", cut into a piece of or separate. So it is necessary to meet the welt width, than to grow to.
Less 1/16 inch (0.2CM), and necklines, shoulder line and waist line shape.
B, stop line along the folding pattern. A collar line, shoulder line and waist line and dart line in origami with description in the shoulder line and waist line
Place to sign.
C draw a straight line between the two symbols, and then draw the shape line (as shown).

北京西服定做官方网站：http://www.skfuzhuang.com/